P-282: 5-Stage GAT /Nordson Powder Coating System
Design: 4’-6” W x 8’-0” H Opening, 10 FPM
System Overview:
- Opening Size: 4’-6” wide x 8’-0” high
- Part Size: 3’-6” wide x 7’-0” high x 12’-0” long, may be modified
- Line Speed: 10 fpm (Variable), <400 lbs capacity, can be increased
- Equipment installed new in 2014/2015
- System offered as is, where is or removed and loaded.
- Item Listed on 12/04/2025
6-Stage Stainless Steel/Poly Pretreatment Washer System
- Additional Stages if required may be quoted by AIS.
- Stainless Steel Tanks & Drainboards with Polypropylene Wall Construction
- 165’-0” long x 8’-6” wide x 14’-5” high + fans and piping
- Gusher Stainless Steel Vertical Mount Pumps
- Quick disconnect risers & quick-change nozzles,
- Boiler Heat with Heat Exchangers on stage 1 & 3
- Fume Scrubber on Entrance, Exit Exhaust fan @ 3hp
- 20’ Drainbacks
- Wash Stages @ 10 FPM
- Stage 1 – 84 Sec. Heated Acid Pickle, 3 pumps @ 7.5 hp ea, 2,525 Gal.
- Stage 2 – 30 Sec. Rinse, 1 pump @ 7.5 hp ea, 868 Gal.
- Stage 3 – 60 Sec. Heated Cleaner/Phos, 2 pumps @ 7.5 hp ea, 1,815 Gal.
- Stage 4 – 30 Sec. Rinse, 1 pump @ 7.5 hp ea, 868 Gal.
- Stage 5 – 30 Sec. Rinse, 1 pump @ 7.5 hp ea, 868 Gal.
- Stage 5 – 30 Sec. Conversion Coat, 1 pump @ 7.5 hp ea, 868 Gal.
Infrared Booster Cure Oven
- Dimensions: 6’-0” wide x 47’-4” long x 15’-1” high, + BB & fans
- Time Cycle: 5 minutes @ 10 FPM, Temp
- Heating Medium: Vulcan Gas Catalytic I/R Heater – 36 Heaters
- Exhaust Fan: 1,061 cfm – 1 hp
Combo Dry-Off & Convection Oven
Overall Dimensions: est. 6’-8” wide x 39’-5 1/2” long x 15’-1” high, + BB & fans
Dry Off Oven Specifications
- Time Cycle: 3 minutes @ 10 FPM, Temp < 350℉
- 2-Pass Design
- Heating Medium: Recirculating, direct gas fired
- End-Mount Burner Box, 24,875 cfm @ 25 hp
- Floor Mount Duct, 2 ea Air Seals with 4 ea 2 HP fans
- 2,400,000 Btu Capacity Eclipse Burner, 3/4 hp & Honeywell Controls
- Exhaust Fan, 1,526 cfm, 1 hp
Cure Oven Specifications
- Time Cycle: 38 minutes @ 10 FPM, Temp < 450℉
- 6-Pass Design
- Heating Medium: Recirculating, direct gas fired
- 2 ea End-Mount Burner Box, 36,000 cfm @ 40 hp
- Floor Mount Duct, 2 ea Air Seals with 4 ea 2 HP fans
- 2 ea – 2,400,000 Btu Capacity Eclipse Burner, 1/3 hp & Honeywell Controls
- Exhaust Fan, 3,491 cfm, 2 hp
- Purge Fan, 3,491 cfm, 2 hp
- 6” thick panels, B-deck insulated floor
- Oven can be reconfigured, Ships knocked down
Conveyor – X458 4” I-Beam
- 400 lb Single Hang Point Capacity
- 1,035 feet of X458 Conveyor
- Trolleys with H-Attachments spaced 24” On Center
- Conveyor drive w/ variable speed control
- Chain Tensioner, Auto Take-up
- Auto lubrication system
- Floor Mount Supports
Environmental Room
- Dimensions – 35’ long x 33’-6” wide x 20’ long
- (1 Lot) 3” Thick insulated panels, Structure, Trim
- (2) Man Doors
- (2) Double Man Doors
- (1) Roll Up Door
- (1) 25 Ton HVAC System
Nordson Colormax Powder Auto/Manual Booth System
- Colormax Booth Base Assembly
- Apogee Upper Housing
- (2) Automatic Gun Openings with Automatic Gun Cleaning System
- (2) Manual Operator Platforms with Stairs
- (1) Nordson After Filter Dust Collectors
- (1) Twin Cyclone with Nordson Powder Transfer System
- Lot Ductwork and Slide Gate
- Lot Transfer Pump Kits
- Encore Powder Feed Center
- Lance Assembly with Pickup Tubes
- Vibratory Sieve
- (4) Fluidizing Hoppers
- iControl 2 Automatic Gun Control System with PLC Master Control
- (16) Encore Automatic Powder Guns with Cables & Hose, Tube Mount
- (2) Reciprocating Gun Movers with In/Out Positioning
- Banner Automatic Gun Triggering System
- FS10R-30 Fire Detection System
- Explosion Suppression System
- Lot System Control Panels
Equipment Price: $600,000 as-is with removal by customer.
Removal and Loading on trucks: Quoted upon Request
Removal & Installation services are available and may be quoted per customer request.
Contact Nick @ 920-361-5208 x 2 or nick@americanindustrialsystems.com for more info or question